How to change the faucet in the bathroom with their own

If you are interested in how to change the faucet in the bathroom, it means that you have come to the address and the material that is given below will help you to figure it out. First of all, it should be borne in mind that such taps can be overhead and recessed, therefore only equivalent replacement is possible here.

But if you, for example, want to install a faucet on the side of a bathroom instead of a laid-on appliance, then this will no longer be a replacement, but a complete installation with the distribution of water pipes. Based on this, we will talk exclusively about replacing overhead options, find out what they may be, and present to you the video in this article.

Mixer replacement

How to choose

A two-valve model of a crane with a shower head, as in the photo, as a rule, has a crane box, most often of a ceramic type, as a shut-off valve. That is, the bush itself is made of brass, but the basis for the regulatory moment there are two ceramic plates with holes.

There are also axle boxes with a worm gear, where the flow is adjusted with a rubber valve mounted on the end of the stem. Thanks to the worm gear, it can move back and forth along the body, closing or opening the passage.

Manufacturers recently prefer the first option, since it is more ergonomic - the full cycle is only half a turn (sometimes a little more) of the valve, while the second option can be from 5 to 10 turns.

Users are interested in how much it costs to replace the faucet in the bathroom, but this, first of all, depends on the device itself. And it is quite natural that a half-turn crane will cost a bit more. But if you do this work yourself, you will save on installation.

The advantages of such units include the fact that the crane axles can not only be replaced with new ones, but also repaired, which extends the service life of the device with free maintenance (repair of the left or right axle box).

The disadvantages include the need to set up two valves at once, for example, if you set the desired water temperature, then after turning it off, the entire setting process must be repeated again.

Note. It should be noted that shut-off valves in the form of a crane-boxes can be not only in valve (thumb) valves - instead of them there can be two small levers for adjustment that perform the same function. So if you are interested in how much it costs to replace the faucet in the bathroom, then do not forget that you also need to pay for the design of the model.

In the same way, replacing a mixer in the bathroom with their own hands can be done with a single-lever model, whose stop valves consist either of a cartridge or of a ball with holes.

As in one, and in another case, the replacement of the locking mechanism is possible, but its repair does not make sense - the cartridges are made non-separable. But for ball valves, you simply can not find parts separately (rubber cams, springs, cuffs).

Nevertheless, they can always be replaced with new ones and if it is difficult to find the ball repair, due to the rare use of such models, the cartridges are sold in all stores of the sanitary direction.

Joystick mixers have one undoubted advantage - after you have adjusted the water to the desired temperature, when closing and opening the faucet you can leave the lever in one position without shifting it to the left or right - so the temperature will be the same all the time.

This is very convenient when shower heads are used frequently, for example, in shower cabins or boxes, although the instruction does not specify exactly where and what type of mixer to install. It should be said that long-spout taps, which serve both for the bath and the sink, can be both two-valve and joysticks.

Attention! For those who are looking for information, how to change the faucet in the bathroom (or the most) - the type of stop valves has nothing to do with the dismantling and installation of the device itself. The above information is provided so that you can choose the most appropriate model in your case.

We make a replacement

This is a must-see! Before replacing the faucet in the bathroom with your own hands, be sure to turn off the hot and cold water. If your faucets are old and the water prokopat little, it is not critical - the replacement can be easily made in such conditions.

• Now go directly to how to replace the mixer in the bathroom with your own hands. and if you have already blocked the water, then you can unscrew the nuts on the eccentrics, by the way, on the old models these nuts (they are both fastening and decorative) are often located on the eccentric side, therefore, you will have to unwind them in a clockwise direction.
• Considering that the size may fluctuate, in this case it is best to use an adjustable wrench for disassembly.. Unscrew them from both sides and remove the mixer - it is no longer needed.

• Now you need to unscrew the old eccentrics and do it most conveniently with pliers - insert one of the jaws inwards and twist counter-clockwise.
• If you can not tear the thread from the place, then insert the same wrench as a lever between the handles - it will be much easier to turn. After dismantling, clean the fittings from dirt and rust - they will be there.

• We continue to consider how to change the faucet in the bathroom, but now the process of working with us will begin to flow in the reverse order, and we will begin by screwing in the eccentrics. The part that you will wrap in the fitting must be reeled up with 4-6-6 layers of fum-tape (depending on its thickness).
• Just do it against the progress of the thread (pay attention to the top photo), from right to left, then when twisting the tape will not crawl. To be sure, smear the tape or fitting from the inside with UNIPAC paste - it blocks leaks when adjusting the eccentrics, and twist them with open-end wrenches for 12, 13 or 14, depending on the model.

• Since we do the work ourselves, the question of how much it costs to change the faucet in the bathroom, refers only to the appliance itself, therefore, at the moment we are not interested. We will now screw it on the installed eccentrics (without fum-tape and UNIPAK paste - there are rubber seals under the nuts), we only clamp the nuts at the same time to avoid skewing.

Conclusion

Now you have an idea how to change the faucet in the bathroom, but given the fact that you can have an old model (metallic), the fittings may not be on the same level.

To do this, they actually need eccentrics, but their final adjustment can be made by screwing a tap on them only by half. After that, remove the mixer, wind the decorative washers and re-tighten the tap.

Successes!