Coloring pipes: calculation of flow and tips on applying

08-08-2018

Pipes

The process of painting pipes is almost the same as other surfaces. However, if you pay attention, then all prices for this type of work are given in meters. In this case, the coloring of pipes in m2 is considered only to determine the consumption of materials.

Calculations and application process

Before starting work, it is imperative to establish the necessary amount of dye. This is especially important if the area of pipe painting is quite large and overrun can lead to high costs. That is why this process must be approached very responsibly.

A special table, which presents ready data on the internal and external diameters of various products with an indication of the areas

Special programs

First of all, it is necessary to pay attention to the fact that it is quite difficult to calculate the color of pipes without the help of special software.

The fact is that you will have to face a number of arithmetic operations or resort to a complex formula.

The program interface, which gives the necessary data based on the types of products specified in GOST

Given these difficulties, experts recommend using a pipe square calculator. It is worth mentioning that such software can be found for almost any platform, which means that it can be installed even on a mobile phone.
Usually a pipe color calculator is designed for specific diameters and accepted standards.. However, this software does not give the amount of dye needed, since it depends on the composition used.

A complete calculator to perform various calculations related to this type of material

Some programs of this type may change their readings depending on the material of manufacture, which must be selected in the interface.. This will help not only to calculate the color of the steel pipe with the most minimal cost.

Tip! When entering data, special attention must be paid to the values. Experts recommend immediately remove all sizes in centimeters to avoid confusion, which will lead to incorrect results.

Some types of pipelines on a mandatory basis are specially marked with different colors, which characterize the type of substance used in them.

Drawing

For a start it is worth noting that the area of the pipe for painting does not have a flat surface, which means that separate attention should be paid to the choice of the appropriate tool. This is especially important if the structure is mounted in an awkward position or too close to other objects. This issue should be solved by the master at the place, focusing on the specific location and finances.

There are special systems that allow internal painting, but such works are rarely performed, because experts try to select the right type of material right away, rather than protect it.

It is important to mention that the calculation of the area of painting the pipes will be needed not only to use the dye, but also when ordering a primer. At the same time, professionals advise purchasing this material with anti-corrosion additives.

It is much easier to use the sprayer, but sometimes the feature of the location of the structures simply does not allow it

Special attention is paid to the choice of the dye. The fact is that the typical installation manual recommends the use of hammer compositions for these purposes, which are usually endowed with additional properties that allow the composition to be applied directly to rust. This will solve the problem associated with the preparation and cleaning of pipes before painting.

Tip! Professionals recommend applying on pipes with a large diameter, using a sprayer. The rest of the system can be painted with an ordinary brush.

Some types of tools were specially designed to work with these structures in case of their inconvenient location.

Recommendations of specialists

If the work is done by hand, you can make approximate calculations. In this case, the remaining paint is useful in the work of preventive maintenance or repair.

Using a special roller, you can significantly ease your work and shorten its duration.

Recently in the market of building materials you can find brushes with curved handles. These tools are great for painting hard-to-reach pipe spots.
Usually the price of paint that can be applied over rust is quite high, but this cost is quite justified if you consider that you do not need to purchase and apply a primer.
When working indoors, it is necessary to immediately organize a constant access of clean air and use personal protective equipment. Virtually all types of paint used for pipes are toxic.

Most hammer paints are not only applied directly to rust, but also have an excellent appearance when dried.

Conclusion

After studying the video in this article, you can get a more detailed picture of this operation and the necessary calculations. Also, taking into account the text that is presented above, it is necessary to conclude that sometimes it is much easier to use special software than to independently determine the required amount of the mixture for coloring.