How to effectively eliminate clogs: soda and vinegar for

17-02-2018
Pipes

Sewage clogging is one of the most unpleasant problems that can arise during the operation of the drainage system. To eliminate it, you can call a plumber who has the necessary equipment or use chemicals. But knowing how to clean the sewer pipe with soda and vinegar, you can effectively deal with the accident with your own hands, saving both time and money.

Soda and vinegar - effective means of combating blockages

Causes and methods of eliminating blockages

Partial or complete blockage of the internal lumen of the drain pipe, that is, well-known and unloved by all, is formed in the sewage no matter how carefully you use it.

The causes of traffic jams are most often:

  • hair falling into the pipeline while washing in the shower;
  • organic residues;
  • soap deposits on the walls.

The first signs that indicate that the drainage system requires cleaning the pipes with soda and vinegar is a decrease in the rate of water runoff, as well as the appearance of an unpleasant smell of sewage.

A blockage in the sewer system does not allow the system to operate normally.

Most people, when detecting a blockage, seek help from private specialists or relevant firms. However, the price of their services may be too high.

Some people buy various chemicals in stores that melt and destroy garbage in pipes. But they can have a negative impact on human health.

To clean the pipe most effectively, cheaply and safely for health with soda and vinegar. These ingredients are available in any kitchen, and the resulting result is unlikely to leave you disappointed.

Tip! Before using various substances to flush the sewer system, it is advisable to disassemble and clean the drain siphon. Perhaps the problem will be solved. In addition, this event will allow more effectively to get rid of the blockage formed in the depth of the drainage network.

Folk remedies in the fight against blockages

Vinegar and soda as a cleaner

The use of sanitary cable is undoubtedly very effective. But, firstly, it needs to be purchased, and secondly, during its use, you severely pollute the kitchen or bathroom, and therefore you will need to carry out additional cleaning.

Photo plumbing cable

Chemicals are also effective. However, in this case, you can not be sure that the excreted vapors do not harm your body.

And knowing how to clean the pipes with soda and vinegar, you can effectively remove the blockage, as well as remove the unpleasant smell from the sewer, being sure of your own safety.

To complete the whole procedure you will need:

  • baking soda, which is used in cooking;
  • vinegar without aromatic additives and dyes;
  • boiled water (the more the better);
  • a rag with which you can plug the sink hole;
  • rubber gloves, brush and plunger.

Note! Using the tools described above, you can only get rid of blockages that are formed by organic residues or small particles. More serious traffic jams require the use of radical methods: cable, hydrodynamic washing and so on.

The instruction is absolutely simple.

Cleaning pipes with soda and vinegar is as follows:

  1. Half a standard box of soda is poured into a drain hole. Keep the powder dry and not mixed with water or other liquids.
  2. Then half a glass of ordinary table vinegar is poured into the sewer.. Before that, it is recommended to warm it up a little. Then the drain hole must be plugged with a cloth or napkin, ensuring as tight a seal as possible.
After falling asleep soda, pour vinegar there too

Soda, mixing with vinegar, begins to form a large amount of foam, which can spill out of the pipe. A rag will help to avoid this. All matter should be distributed in the internal space of the sewage system, dissolving the blockage and pushing the garbage down.

  1. The mixture is left in the pipeline for 30-40 minutes. This time is necessary in order for the foam to completely dissolve the existing plug, which does not allow dirty water to pass to the riser.
  2. After the allotted time, you need to boil a full kettle of water, remove the rag from the drain and pour all the existing boiling water into the hole.
Rinse the hole with boiling water.

At this flush is over. If the pipe is not restored, the procedure should be repeated as many times as necessary.

The toilet can not be cleaned this way, as you cannot plug the drain hole. It is better to use just soda and plunger. This will help not only to remove the blockage, but also to disinfect the sewer.

Using soda in combination with other substances

Cleaning sewer pipes with soda and vinegar is not the only way to use it. The substance can also be combined with salt and tartar.

In the first case, you will need:

  • 0.5 cup soda;
  • 0.5 cups of salt.
Salt helps to clean the drain

It is necessary to pour both ingredients into the drain hole, then pour a large amount of boiling water there and leave everything for 8-10 hours. During this time, liquid or other substances should be avoided.

Very well eliminates organic deposits of tartar mixed with soda and salt.

The mixture must be done in such proportions:

  • 1 cup salt;
  • 1 cup of soda;
  • 0.25 cup of tartar.

All components are thoroughly mixed and left in the box for 7-10 days. Then the mixture is poured into the hole and after 5 minutes, washed with plenty of cold water.

Tip! The methods described above can be used for prophylaxis. Periodic flushing of the waste system with a mixture of vinegar and soda allows you to completely avoid the formation of blockages, saving you nerves and money.

Mechanical cleaning

To make pipe cleaning more efficient, directly after pouring boiling water into the hole, you can additionally use a plunger, which will help eliminate the blockage by creating excessive pressure in the pipeline.

To do this, place the rubber part of the plunger over the hole and repeatedly press the handle of the device. You must first close the overflow holes, otherwise you will not be able to move the clog.

After the shocks, you can sharply tear the rubber cap from the surface of the sink. As a result, the garbage is thrown out through the drain.

Scheme of use of the plunger

Conclusion

Soda and vinegar - an excellent tool for cleaning sewer pipes. With their help, you can get rid of obstruction, unpleasant smell and bacteria that live in the drain system. The main thing is to strictly follow the procedure described above.

In more detail about methods of recovery of working capacity of sewer systems it is possible to learn from video in this article.