Flow of the toilet: the place of appearance and repair

03-01-2018
Sewage

The toilet is the original type of construction of the water supply and sewage systems, which not only combines these highways, but also constantly has a certain supply of liquid inside. It should be noted that the water supply and its control is carried out automatically. That is why the flow of water in the toilet must be fixed immediately when it appears, because even a small leak can lead to flooding.

Amateur photo of the internal arrangement of the toilet with the water level

Types of defects and methods of their elimination

First we need to say that this article will address technical problems that can be fixed with the help of tools or additional materials. Elementary damage to ceramics, expressed by chips or cracks, should be fixed with the help of special putties. However, with such damage it is worth making a complete replacement of the toilet, although the price of this device is quite high.

Subject indication of all elements of a standard toilet bowl cushion design

System Setup

  • Quite often during the operation, breakdowns occur that lead to the fact that water continues to flow from the tank even after flushing.. This leads to the appearance of rusty drips and an exorbitant consumption of resources.
Adjustment of the float under a certain water level must be made according to the drawings of a particular design, since each model taken separately may have its own characteristics and methods of adjustment.
  • Usually such a repair of a toilet bowl is done with its own hands in just a few minutes.. It is enough just to re-adjust the level of the float so that the water does not flow through the overflow.
Graphic manual on the correct setting and fitting of the tank fittings of a particular model and for a specific structure
  • Quite often, such defects occur due to the fact that plaque or debris appears at the junction of the valve of the tank and the drain hole.. Therefore, the answer to the question of how to eliminate a leak in the toilet on the sink often lies in the fact that the masters recommend simply to clean this area.

Tip! If the drain valve has the form of a rubber pear, then it should be weighed down with several nuts so that under their weight it fits more tightly over the hole.

The appearance and location of the intermediate gasket between the cistern and the toilet itself

Intermediate gasket

There are such cases when, in the process of operation, a leak appears between the cistern and the toilet when it is drained. This is due to the fact that the intermediate gasket has been damaged or displaced.

It is much easier to immediately purchase a special gasket that is worn on fixing reinforcement as well, since it will not be displaced even under heavy loads.
  • The process of eliminating this defect is that you first need to disconnect the tank from the toilet and remove the old gasket. After that, the seats are carefully wiped, removing plaque.
  • If the gasket is intact, then it is cleaned with the help of hands with vinegar or household chemicals.. However, experts recommend installing back new products to be sure of a long service life.
Even if sand or dirt simply gets onto the seat during installation, this may cause a leak during operation, but usually such a defect occurs only after a mechanical load on a given area.
  • It is important to note the fact that if there is a toilet cistern leak through the overflow and at the same time this defect is present, this can lead to flooding of the room.. That is why both problems need to be addressed almost immediately after detection.

Tip! If the installation of the toilet bowl is done qualitatively, then this type of defect usually does not appear even after certain physical activities. Therefore, the approach to the installation must be very responsible.

Graphic representation of the drain of drain water due to irregularities at the junction of the sewer pipe

Sewage

Very often, the problems of maintenance and repair of such structures are not limited to the questions of how to eliminate the leakage of the toilet bowl. Sometimes the problem occurs at the point of connection of the tank to the sewer pipe. This is especially expressed during the descent of water.

The organization of such a junction when using old cast-iron pipe, which is not going to change

The main feature of such a breakdown is that it is very difficult to detect. It is not human nature to peek under the toilet while draining water, and if the leak is small, then it is almost invisible.

Even a slight bias can dislodge the gum seal and cause dampness and even leakage with each flushing of water from the tank.

The answer to the question of how to clean the leak in a toilet of this kind usually involves replacing the coupling. However, what to do if the installation of the device occurred with violations or the gap arose due to the design and location.

The use of a sealant or silicone putty makes it possible to eliminate only small cracks or cracks, for larger defects you need to use cement

Professional masters in such cases offer to use special sealant and tape, with which they cover the place with a crack or gap. You can also use ordinary cement and medical bandage, which in the manner of gypsum make a special patch around the joint.

Tip! When planning this room, it is necessary to take into account that some models of toilet bowls need a certain space for high-quality installation. This will avoid the occurrence of such problems.

The use of a special corrugation or rubber coupling will avoid such problems even in places where the connection is made at the most unexpected angles.

Conclusion

After reading the video in this article, you can get more detailed information about these types of breakdowns and their elimination. At the same time, on the basis of the text carried out above, it is necessary to conclude that if the initial installation was carried out correctly, then in the course of operation such defects should not appear.