How to independently repair the sewage
No matter how efficiently and reliably the sewage system is completed, sooner or later it will necessarily require repair. There are quite a few reasons for which the system may fail, respectively, the troubleshooting methods are also different. Therefore, in this article we will look at how to repair sewage in different cases.

General information
The sewer network is a piping system to which plumbing fixtures are connected. Sewerage is perhaps one of the most important elements, providing comfortable living in a house or apartment and the load is quite high.

So, do not be surprised at the various faults that occur from time to time. Most often, their causes are physical deterioration of the system or malfunctioning of the sewage system. Most often, repair the sewer pipes with their own hands to eliminate these faults, every household master can do.
Blockages
The formation of blockages - are the most common cause of sewage failure. A “cork” of debris can form anywhere in the aqueduct, however, the turns of the pipes are the most vulnerable. Therefore, in complex areas, an audit is established, i.e. hatches through which you can clean the pipeline.
If the blockage is minor, i.e. water passes slowly, then you can try to eliminate it with a vent. To do this, the rubber bulb should be placed above the drain hole and make a few active strokes. As a result, hydraulic shocks are generated in the system, which can destroy the plug.

If the blockage is serious and the plunger does not help, then the plumbing wire that pushes through the sewer line to the point of clogging will help to solve the problem, after which its end breaks the plug. It is more convenient to work with the cable together - one person pushes the cable into the pipe, and the other turns the handle so that it rotates.
Note! When working with a cable, it is necessary to ensure that it is always in a tensioned state. Otherwise, the cable will twist and work with it will be impossible.
Leakage
Leaks in the pipeline appear for two reasons:
- Depressurization of pipe joints;
- Mechanical damage - crack or fistula.
To eliminate leakage at the joints is quite simple - you can reel tow, which fits into the socket. If the leakage is caused by mechanical damage, then the repair of sewer pipes in the apartment depends on the material from which they are made.

Plastic pipes
If a crack is found in a plastic sewer pipe, then the problem can be resolved in the following ways:
By soldering | To perform such a repair you will need a special apparatus for sealing plastic pipes. |
By applying epoxy glue or putty | It is a simpler repair option, since it does not require special equipment, but for that it takes longer, since it will take some time for the glue and putty to freeze. Most often, this type of repair is temporary, as it is not very reliable. |
Pipe replacement | The most difficult type of repair, but at the same time, the most reliable. It may be necessary if the pipe is badly damaged. |

Cast iron pipes
If a leak is noticed on a cast-iron riser, which cannot be replaced in the near future, the following actions can be taken:
- If the flow is weak, then you can eliminate it with a small amount of cement. For this, the place around the crack should be cleaned with sandpaper, then apply a little cement.
- If the leak is more serious, then you can eliminate the problem by applying a clamp.
- Another widespread way to repair cast-iron risers is with cement and a bandage. A cement mortar of plasticine consistency is applied to the site of the crack, after which the site is wrapped with a bandage. The top layer of the bandage should be smeared with silicate glue.
Tip! Silicone sealant may be used to repair minor damage.
Outdoor networks
In a private house sewer system is not limited to the internal pipeline, as the malfunction may occur in the external networks. In this case, the so-called trenchless sewer repair is performed.

It can be executed in the following ways:
- With the removal of the old pipe and pulling new.
- Without removing the old pipe - in this case a pipe of a smaller diameter is used, which fits inside the old one.
I must say that this operation is quite complicated, especially if it is necessary to remove the old pipe. Therefore, it is better to seek help from specialists. True, the price of such services may be high.
In addition, in a private house repair of sewer wells may be necessary - it is necessary to ensure that its walls do not crumble. If necessary, concreting or restoration of the masonry may be required.

Storm sewer service
Repair of storm sewers, which owners of private houses also face, as a rule, consists in flushing the system. To do this, usually use a special technique that allows you to wash storm sewer under pressure.
The rest of the maintenance of this system is to clean it from leaves and other debris that can interfere with the normal discharge of rainwater. Here, perhaps, and all the instructions for troubleshooting sewer systems.
Conclusion
As we found out, in most cases, you can repair the sewage system without the help of specialists. The only external repair of sewage systems in a private house can cause some difficulties, since the pipes are usually located deep underground.
From the video in this article, you can get more information on this topic.