If the sink in the kitchen or bathroom clogged

Plumbing fixtures may occasionally fail, primarily due to clogging. Thus, the question arises as to how to clean the sink: if it is clogged in the kitchen or in the bathroom, it may not allow water to flow into the sewer system at all.

In this case, it is necessary to resort to emergency measures.

Preventive actions

It is possible to cope with congestion by applying several methods, but it is better to prevent the formation of garbage jams, following special recommendations.

Even if you can not completely get rid of clogs, in any case, it will be possible to reduce their frequency of occurrence.

• Do not drain leftovers from the dishes directly into the sink. Before washing, they must be cleaned in the trash.
• Minimize the ingress of solid particles into the interior by installing a metal mesh.
• It is better to install metal elements, since they are not susceptible to corrosion, which means that rust will not accumulate.

Note! Above were given the main recommendations for operation, indicating what to do: if they are observed, the risk of congestion will be reduced to a large extent.

Solutions to the problem

When a blockage has occurred, it is necessary to proceed directly to its elimination, but this can be done in several ways. The choice of option will depend on the degree of contamination and the availability of available tools. With regard to the tools used, the following are the techniques that allow to do without complex tools.

Impact of the plunger

This item is quite simple from the point of view of the device, so its price is low. With this type of tool you can get rid of most congestion in the sink.

A plunger while lowering increases the pressure, which causes pushing through the mash. When it rises, the impact decreases, so the garbage can is destroyed.

The algorithm of operations is reduced to uncomplicated actions. First, some water is poured into the bowl of the sink, after which the tool is installed just above the drain hole.

The handle of the plunger is pressed 2-3 times. The power of water hammer depends on the strength of the person.

Chemical method

For cleaning, you can use a special technique that involves the use of chemically active substances. On counters of shops a large quantity of special means is offered. However, if necessary, you can use the improvised components.

Cooking instructions are listed below.

1. First you need to boil the kettle, so use water for cleaning, the temperature of which is at least 90 degrees.
2. Half a glass of baking soda falls asleep directly into the drain hole. It is in almost every home.
3. Then about the same amount of vinegar is poured. This component is also not very difficult to find.
4. After 2-3 minutes, you can flush with hot water. A chemical reaction will start that will get rid of the blockage.

Note! For prevention, you can use a special mixture consisting of baking soda, salt and tartar in the ratio of 1: 1: 0.25. In the sink fall asleep? cup composition, after topping up with boiling water.

Siphon disassembly

If the methods proposed above did not have the desired effect, then you can try to disassemble the elements under the sink with your own hands. The siphon is located under the drain hole of the sink or sink. It is a product in the form of a bent pipe filled with water.

The basic function of this design is to isolate odors from the sewage system. Clogging is due to the accumulation of solid particles at the bottom. Before cleaning the siphon, it is necessary to substitute the container under the sink so that dirty water does not spill onto the floor.

When disassembling you need to adhere to a specific sequence of actions, then you will be able to avoid difficult moments.

1. With a wrench, the bolt is unscrewed to hold the cleaning cover. At the bottle counterpart, the sump can be unscrewed directly by hand.
2. The water contained in the siphon should be completely drained into a pre-prepared bucket, after which the elements should be cleaned with a wire.
3. After completing the cleaning measures, install all the parts in place. It is recommended to perform sealing before installing them. For this purpose, a special compound is applied to the threaded connection.
4. At the last stage, it remains to check the operation of the system.. Water should quickly go with an average pressure.

Attention! If, after disassembling and cleaning the siphon, the water does not pass at all or is drained very slowly, then with high probability we can say that the blockage is in the pipeline.

Use of plumbing cable

Another way to get rid of debris inside the siphon involves the use of a flexible shaft that is able to penetrate into hard-to-reach places. Usually a metal brush is placed at its end, and the cable itself may even rotate. The drive, as a rule, is carried out by means of usually drill.

As a conclusion

In the event of congestion, the information provided will help you understand what to do: if severe contamination has occurred, then one of these options should help in almost any circumstances. All methods of getting rid of traffic jams are quite simple and do not require serious financial investments.

You can learn more about this topic if you read the video in this article.