Installing the sink in the countertop - the work that

Many people think that installing a sink in a tabletop on their own cannot be done without special experience and tools. In fact, everything is not as difficult as it seems at first glance, besides, you can save considerable funds, since the cost of this type of service is quite high. We will consider in this review how to properly organize the workflow to do everything in accordance with the technology.

What is needed for the work

Before you install the sink in the countertop with your own hands, you should stock up on some devices and materials:

Tip! If you have a countertop made of natural or artificial stone, it is better to purchase the option with a ready cut for the sink, as cutting it at home is not for the faint-hearted. Not only is the work quite complicated and time consuming, so even in the process of work just a huge amount of dust is formed - the whole room will be polluted.

How to install

All work can be divided into two main stages - preparation of the table top and installation of the structure into place with the addition of all necessary communications. It should be noted that the installation of a sink made of artificial stone in the countertop is no different from working with structures made of cast iron and stainless steel. Works are always the same and must be done in a certain sequence.

Sidebar

Consideration of the question of how to install a mortise sink in the countertop, begins with the preparatory work:

• To begin with, check measurements of all elements are made.. In order to simplify the workflow as much as possible, it is best to make a piece of cardboard, in some models of the sinks it already comes in a set, which is very convenient, because you just need to cut it out of the packaging box along the contour previously marked. The use of such an element will not drag the sink, which is very convenient, especially when it comes to products made of stone.

• Next, you need to apply the markings on the surface, it is very important that it be as accurate and smooth as possible, without distortions. In order for the system not to move in the process of marking, you can fix it with ordinary masking tape or tape.
• After the contour has been applied, it is necessary to measure the width of the support rim, since this part will lie on the surface. Further, the contour is reduced by the width of the supporting part, for convenience it is also better to draw. It is along this line that the cutting will be made, so make it as accurate as possible to avoid any mistakes and inaccuracies.

• After marking, you can start drilling holes, if the design is square, then you can make them at all four corners, if oval, then most often one point is enough, cutting will start from it, and it will end at it. The drill should be of a larger diameter than the width of the hacksaw blade, that is, the nail file should pass freely into the finished hole.

Tip! Do not forget to make sure that you have an assistant during the work, otherwise it will be difficult to cut a hole, you need someone to hold the cut part and prevent it from tilting and falling until the end of the work, as this may cause damage to the cutting blade.

• Considering the question of how to install a mortise sink in the tabletop, it is impossible not to touch upon such a moment as correct cutting with an electric jigsaw. This should be done as carefully as possible, do not click on the equipment, it will move quickly enough by itself, it is important not to stray from the intended line, especially if it is not straight, but rounded. Another recommendation is to choose a blade with the opposite direction of the tooth, then it will not damage the upper edge.

• After work, you should try on the sink, if everything is normal, you can proceed to further activities.

Installation

We will continue to consider the question of how to properly install the sink in the countertop, further work is also very important:

• First of all, it is necessary to clean the end of dirt and dust, it is necessary in order to seal it. To protect against moisture, a colorless silicone sealant is used that is resistant to mold and mildew and has excellent waterproofing properties. It is best to apply it with a pistol, but you can do with an ordinary hammer by inserting it with a pen into a tube and pressing it when applying.

• A special sealing tape is glued around the perimeter of the sink, which most often comes with the sink, it is self-adhesive, and the only recommendation for its installation is to degrease the surface, especially if you install the stainless steel sink into the tabletop, the metal needs additional processing.

• Before you install the sink in the countertop, it is necessary to put on special fixing elements, since after this it will be much more difficult.
• After installation, the clamps are clamped to make the structure still, do not be too zealous, as you can damage the surface.

This simple instruction will help you to easily figure out how to install the sink on the countertop, it is worth noting only the fact that the connection of the mixer can also be done in advance, although later it is easy to do if there is free space under the sink.

If you are interested in how to install a wall-mounted sink on a tabletop, then a few facts should be noted:

• Such structures are most often installed on a special cabinet and are not intended to be mounted on a flat surface, although there are options with special pedestals.
• Sewerage and water supply are brought differently, so be prepared for additional work.
• This option is not very good for kitchens, as it is located high, and in the process of use it will not be very convenient for all households.

Conclusion

It is not only interesting, but also economical to install the sink yourself, because the price of this service is quite high. The video in this article will clearly show the most important points of the workflow and help you understand it even better.