Integrated sink: embedding directly in the countertop

In the kitchen, before cooking and after this operation, work is done using water, so the installation of a special device is simply necessary. The integrated washing is especially popular: what it is, you can find out if you read the information below.

Main advantages and disadvantages

This category includes products intended to be built into the tabletop, and the installation can be made either flush with the surface or shifted down or up.

This option has its pros and cons, which can be found below. Depending on aesthetic preferences and operating conditions, a final decision should be made about the purchase.

The most important benefits

• The price of products is quite comparable with analogues of other types, but the final cost will depend on the material of manufacture.
• Introduction to the surface of the tabletop allows you to achieve an impressive aesthetic effect.
• A wide range of products of this type provides excellent opportunities in terms of design solutions.

Negative points

• The installation process is quite complicated, but it is still quite realistic to do it yourself, especially if you have experience.
• Poor sealing of the joint can lead to moisture between the product and the end of the table top.

Note! Countertop with integrated sink can be made of different materials, so the characteristics may vary slightly depending on the model being purchased.

About installation options

Mounting technology involves the embedding of products in various ways, each of which is able to affect external perception. All there are three options for placing products on the surface of the tabletop.

After reviewing them, you can make a choice in favor of one of them.

• The location of the sink above the level of the plane is most often. Usually the construction of the edges rests on the tabletop. Special brackets are used as additional fasteners.
• Placing the product flush with the surface allows you to create a single plane without any protrusions. In this case, the cleaning process is greatly facilitated. However, the sidebar should be carried out with maximum accuracy.
• The installation of the sink below the level of the bollard has recently been performed quite often.. With this option, the end part is visible, so this method is most relevant for stone and plastic countertops.

Note! Whichever method of installation is not finally chosen, the quality of the work performed is of particular importance. It is most difficult to install the structure on the same level as the surface, since the accuracy of the cut is very important here.

Materials used

Stainless steel is widely used in the manufacture of kitchen sinks, as it allows to obtain durable, but not very expensive products. Unlike traditional material, alloyed alloy contains chromium, which protects against the occurrence of corrosive processes.

No less popular products from artificial stone, which can not be attributed to the category of expensive goods. An alternative to the natural counterpart can be made from synthetic compounds based on polyester resins or colored concretes. As a filler, as a rule, a crumb of natural minerals is used.

Not lost popularity and products and ceramics. Currently, sinks are made of earthenware, porcelain and some other materials. They are especially relevant in classic interiors, but many models can be successfully implemented in any modern interior.

Integrated products are made not only from the listed materials. In kitchens, there are sometimes models of natural stone, plastic and non-ferrous metals. When choosing, it is necessary to proceed from the conditions of use and decorative features.

Basic installation steps

The installation process can be divided into separate stages that are relevant to all types of products. Further installation instructions will help carry out the work independently.

The main requirement is to strictly follow the procedure.

1. The markup is a preliminary stage, but no less important than the rest. Usually, a special template that comes with the product is used as the basis.
2. The insertion process is performed strictly according to the markup made. Most often, work is done using an electric jigsaw. The initial hole is made by a drill.
3. The insertion of the shell with the subsequent sealing is carried out immediately after the creation of the notch and the processing of the ends. In the process of sealing joints means is based on silicone.
4. Fastening the product is the final stage of work. In many cases, the locking parts are supplied with a sink, but if necessary they can be purchased separately.

Attention! It is desirable to insert a siphon and install the faucet on the sink before inserting the structure into the prepared hole. Otherwise, you can significantly complicate the installation work.

As a conclusion

The considered information regarding integrated models of kitchen sinks will help to better navigate a wide range. Familiarization with the installation technology will allow installation on your own, because the rejection of the services of professionals provides an opportunity to significantly save. A clearer picture of this type of product allows you to get a video in this article.