Shower corners with a low tray. materials for the
To save space is usually used shower box, which is designed for location in the corner of the room. To facilitate the operation of this design, set the pallet with low walls. As for the linear dimensions, their choice is made taking into account the characteristics and dimensions of the bathroom.

Positive and negative points
Before acquiring models of this type, it is recommended that you learn more about the pros and cons of this option. In some cases, the choice in favor of such products will be justified, and in others - not. So, the main advantages and disadvantages are outlined below.
The most important advantages
- The affordable price of the product allows you to do without serious damage to the family budget.
- A high level of security is ensured due to the low sides, which is most important for young children and the elderly.
- The finished design, if necessary, can be installed by hand, and this has a positive effect on savings.
- The model with a low pallet looks very impressive, despite the stylistic direction in the design.

The most significant disadvantages
- A shallow bowl products can not be used as a small bath for the adoption of water procedures.
- If there are problems with the discharge of sewage into the sewer system, the probability of flooding the room is quite high.
- At low sides, the pollution in the interior is very noticeable, so the requirements for maintenance somewhat increase.
Addition! If for hygienic measures a shower cabin with a tray with a shallow bowl is used, then care must be taken during the operation, otherwise flooding cannot be avoided.
Little about the selection process
Successful acquisition will allow to operate the structure for a long time with maximum comfort. In this regard, the choice must take into account the basic parameters that are most important. Neglecting even the smallest nuances may be affected when using the device in certain conditions.

Materials for the manufacture of pallets
Bottom designs can be made from a variety of materials that differ in technical characteristics. It is for this reason that the service life in the same conditions will be very different.
This will necessarily affect the final cost of the product.
- Cast iron is an inexpensive, but quite effective material for the manufacture of such products.
- Stainless steel It is not so cheap, but it is rust resistant and easy to clean.
- Ceramics fragile, but it looks quite aesthetic. It is easy to maintain.
- Acrylic - modern material classified as plastics. Products made of it are usually used if the risk of mechanical damage is not very great.

Attention! Regardless of the material used for the production of the structure, experts recommend choosing models with a raised surface so that it is not possible to slip during hygienic procedures.
Basic door types
Sash should be given no less importance when choosing shower products. From their tightness will depend on the dryness of the floor in the room. As for the type of doors, this parameter primarily affects the level of comfort.
Usually the flaps can be opened in two ways.
- Sliding elements are shifted to the side directly to the mounting profile. The main parts are special rollers that simplify the process of movement. They are usually installed in small spaces.
- Swing counterparts can be either single-leaf or double-leaf. The first of them can only open outwards, while others - in both directions. Mobility is ensured thanks to the swivel profiles and hinges. It is not recommended to use sash with an external outlet for small rooms.

Note! Doors for hinged shower cabins are most familiar to people, as they are common in everyday life. However, in confined spaces, sliding doors cannot be replaceable.
Installation
The peculiarity of the shower corner is that there are no back walls, and the guide elements are attached to the side surfaces. In connection with this increasing requirements for site preparation. Planes located perpendicular to each other should not have drops.
Pallet installation
At the very beginning the bottom bowl is installed. In the process of work, the screw legs are set at a level so that the upper part is in a horizontal position. The corrugated hose running from the siphon is fixed to the funnel pipe. After the installation process, all joints should be well sealed.

Side wall installation
To the top of the bowl fits guide rail. Fixing to the surface is carried out using a moisture resistant sealing agent. From this part on each side are installed vertical racks in the same way. When mounted, it is important to achieve a vertical position.
Properly prepared guide elements are worn directly on the walls of the structure. In the course of work small self-tapping screws are used. For sliding doors, guide strips are installed, and hinges are installed for swinging doors.
Sash installation
At installation of these elements it is necessary to observe extreme care as the risk to damage them is rather high. Most doors have special eccentric type rollers. They hook on the guide parts, after which they are easily adjustable. In the closed position, the sash should be connected very tightly so that there are no gaps.

Testing
After completion of the installation, it is mandatory to check the tightness of the assembled structure. For this purpose, a water jet is directed to the joints from the inside. If stains appear, then the seams need to be treated with a hermetic compound.
Means is applied on a dry and clean surface. Retesting is carried out in 8-10 hours.
As a conclusion
If this instruction for choosing and installing corner-type shower boxes will be used with visual aids such as the video in this article, then there will be no particular difficulty with the work. Do not forget about safety when using complex tools to avoid injuries and troubles associated with damage to the finished elements.