What to do - if my toilet is dancing: 3 reasons and ways to

When the repair work in the bathroom and toilet is of proper quality, you can comfortably and safely use both the shower and the toilet. But if carelessness was made during installation or low-quality components were used, certain problems may arise that require immediate remediation. One of the most common questions is what to do if my toilet is dancing?

The search for an answer to it is devoted to the material below.

Causes of the problem

Before you figure out what to do - if the toilet is dancing, you need to establish the causes of the described problem.

It should be noted that this sanitary device is one of the most frequently used devices in residential buildings, commercial and industrial buildings. No building (with the exception of auxiliary) is not built without a restroom, designed for the administration of natural needs.

A securely installed toilet does not cause any problems to the owners of the house or apartment. The biggest trouble is the formation of a blockage. But it occurs only in cases when the rules for the use of sanitary devices are violated.

However, in very rare cases, an established and seemingly tight toilet begins to sway and make unpleasant sounds (that is, your dancing toilet becomes more singing).

This nuisance not only does not add comfort when visiting the toilet, but can also be dangerous to health: flying off mounts or splitting, the plumbing fixture will cause serious injury. Therefore, the question of what to do - if your toilet is dancing, the answer should be sought as quickly as possible.

In most cases, the causes of trouble are as follows:

1. Marriage of the product itself. This is the most common case. Deciding why my toilet is dancing is not necessary. Contact the store that sold you the product for warranty replacement.
2. Improper floor preparation. Here, obviously, the toilet itself is no longer to blame. The responsibility lies with who installed this device. If you sought help from the construction team, call them again. The question of what to do when my toilet is dancing should only bother you if you installed it yourself.
3. Loose mounting. If this is the reason, you just need to tighten the nuts or bolts a little more. More detailed instructions are given below.

Note! Many will ask the question, and what if my toilet is dancing, but none of the reasons listed above have been found. In this case, more thorough examination is necessary. Most likely, you missed something.

For example, the cause of the “dance” of the toilet bowl could be the destruction of the gasket or improper drying of the sealant that was used during installation.

Remedies

Marriage products

It is unlikely that you do not want after the end of the repair to decide what to do - if my toilet is dancing. To insure yourself against this, you need to check the quality of the purchased device from the very beginning. You should get the product out of the package, put it on a flat floor and shake it a little. A quality model will stand straight and not sway.

Otherwise, you must require a replacement device. If this cannot be done (the exchange period has passed, documents have been lost, and so on), one thing remains - to put the toilet on a concrete layer.

This is done as follows:

1. A small amount of mortar is prepared from cement, sand and water.
2. Then a small layer of concrete (about 2–3 cm) is placed on a previously prepared place, after which a toilet is placed there.
3. The next stage is alignment. Smoothly install the acquired sanitary device will help water or laser construction level.

Note! Align the toilet is necessary not only for its comfortable use. Distortions can lead to breakage of the leg, as the force on the fasteners will be distributed incorrectly.

1. Do not forget to fix the toilet with fixing bolts. Cement alone will not be enough to firmly hold it in place.
2. The rest of the materials can be used for arranging the screed in the toilet.

When you do not want to bother with complex construction work, and the question of what to do - if my toilet bowl is dancing, requires the quickest resolution, you can use special silicone pads for the toilet seat. Their price is low and they are in every store, but it is advisable to use them only in the case when the defect is significant.

After installation, do not forget to cut all the protruding parts of the gasket out from under the support, firmly tighten the bolts and lubricate the installation site with sanitary sealant to prevent the formation of mold.

Tip! If the toilet bowl only swings a little, instead of a gasket, you can simply use a sealing gel. To do this, you need to apply it with a thick layer, install a toilet and do not touch it until the sealant is fully cured. In most cases, this should help solve the problem.

Remember, in no case can not trim the leg with a file or grinder. Fragile ceramics will immediately crack and you will have to buy a new plumbing fixture.

Bad mounting surface preparation

Some inexperienced home craftsmen wonder what if my toilet bowl is dancing after replacing it with the old one? Here the reason lies not in the device itself, but in the surface on which it is installed.

Often, after the dismantling of old plumbing fixtures, there are fasteners on the floor, pieces of frozen concrete, silicone fluxes, and so on. If you do not pay enough attention to cleaning the site, you can easily get a dancing toilet that does not add to your mood.

Always gently clean the platform and install new devices. So they will stand firmly and do not collapse from the constant rocking from side to side.

Loose fasteners

The last reason why my toilet bowl is dancing is to loosen the fastener knot.

There can be three options:

1. Studs or anchor bolts simply loosen. In this case, you need to take a screwdriver or a key and tighten the heads stronger.

It is important not to overdo it. Toilets are made of ceramic and too much force can cause cracks to appear in the leg or a piece of chipping from it, causing the device to become unusable.

1. Fasteners come into disrepair.. Most often this occurs due to corrosion, because the toilet is a room with high humidity.

To solve the problem you need to replace the bolts. It is advisable to take accessories, covered with protective compounds, so that it lasts as long as possible.

1. The nest into which the bolt was screwed in was loose. Here you should either screw in fasteners of larger diameter to the old places, or move the toilet to a new place.

In the second case, it is necessary to solve another problem - to connect the sanitary device displaced in one direction or another with the sewer inlet. For this, it is desirable to use a flexible corrugated plastic cuff.

It is set as follows:

1. The toilet pipe and the inlet must be cleaned from the remnants of the old cuff, traces of silicone and rubber gaskets, which ensure the tightness of the connection.
2. All surfaces must be dried, as sanitary gel does not adhere to wet ceramics, which will be used to seal the cuff.
3. Then you need to coat the external surface of the toilet nozzle with silicone and put one edge of the cuff on it. After that, it is advisable to take a break from work so that the used sealer grabs, ensuring a reliable joint.
4. In the same way docking with the sewer pipe. Only need to coat with sealant not a pipe, but a cuff.

Tip! In order not to break the tightness of the connection, do not use the toilet until the silicone sealant has completely hardened.

Conclusion

Faced with the problem of a dancing toilet, do not despair. You just need to find out the cause and eliminate it. The procedure is simple and there is no need to buy expensive equipment.

Much worse if the toilet in your house is clogged. How to act in this case? Watch the video in this article.