Ceramic faucet: features and replacement

If, during the operation of a water faucet, defects such as leakage even after complete closing appear, or an unpleasant sound is heard, then it is time to repair or replace a part such as a crankshaft. It should be noted that previously used similar elements with rubber inserts, which provide a relatively short period of work and require a large number of revolutions to achieve maximum pressure. That is why modern masters use such a detail as a ceramic Kranbuks, which has a lot of advantages and the minimum number of drawbacks.

Characteristics and working principle

First you need to say that such parts have certain standards and sizes. At the same time, a typical device of ceramic cranes makes it possible to install it even on those cranes where elements with elastic bands used to stand. However, with this approach, you should very carefully select a specific model.

Special features

• First of all, it should be noted that such products have a rather long lifetime.. Considering this, repairing a ceramic faucet of an axle box with your own hands has to be done quite rarely and sometimes they are simply changed along with the worn out mixer.

• It is also necessary to mention that in order to get the maximum pressure it is enough to turn the valve half a turn.. However, it should be borne in mind that not all users like such a sink mixer device, although experience appears with a little practice. The same applies to the question of how to repair a ceramic crank box.

• Special attention is given to the fact that such products very poorly tolerate the effects of tap water, in which there is sand. It enters the space of the cavity of the crane with a flywheel and creates the production of ceramics. However, most plumbing systems are equipped with filters that hold these particles.

• It can be said that the price of such elements is rather high compared to products with rubber inserts.. However, if we take into account the fact that the cost of an individual part in relation to the mixer is not significant, then this is quite an acceptable cost.
• Repair and replacement of such systems is very simple and does not require special education from the performer..

Tip! If this part is replaced, it is much easier to take it with you to the market, since in this way the seller will be able to select the most suitable model. The fact is that, over time, such constructions are modernized and refined, which means that it will be rather difficult to find exactly the same product.

Principle of operation

A standard crane box 1 2 ceramic consists of a frame on which plates with holes are fixed. They are installed in the amount of two pieces in special grooves. Naturally, these plates are made of ceramic materials.

When the crane is rotated, the movable part of the axle box is shifted, and the holes are either aligned or shifted closing. Special attention should be paid to the fact that the crane box 3 4 of ceramics usually has larger gaps, although there are also models that have a well-defined diameter that allows you to create a specific flow.

Tip! Professionals recommend using these types of systems, as they are the most practical, reliable and with a long service life.

Repairs

Usually the question of how to adjust the ceramic faucet to the bush is only asked when replacing the plates after a certain period of operation. However, everything is quite simple, since the parts have their own seats. At the same time, after its installation in the mixer, she herself occupies the necessary position and when fixed, she starts working in the normal mode.

It is important to remember that the installation manual strongly recommends very careful with inserts. The fact is that ceramics is quite fragile and with a certain mechanical action it can break. Given this, some masters recommend purchasing already assembled products.

If the construction proceeds after installation, it is necessary to re-disassemble it and see if dirt or sand has fallen into it. It is also recommended to replace all gaskets, if any.

It must be remembered that when working with tools near the mixer, you need to work very carefully so as not to damage the coating. Some masters at the same time prefer to use a rag or a rag, which is placed between the key and the structure, creating a kind of compaction and protection. Professionals in such cases use a special tool that has its own lining or is made of soft material. (See also the article How to choose a siphon for a sink: features.)

Tip! In this process there is nothing difficult, but inaccurate work can lead to violations of operational properties. Therefore, you should not hurry and all actions must be carried out carefully.

Conclusion

Having studied in detail the video in this article, you can get a lot of additional information about these products and their design. Also, taking as a basis the article cited above, it is necessary to conclude that ceramics in such details showed itself much better than rubber and, therefore, it gradually displaces it from this market.