Du50 ball valve: options, sizes, features

27-10-2018

Water supply

A ball valve Dn50 can be used as a stop valve for transportation through pipelines and storage in tanks of various liquids and gases. Such devices differ in the way of fastening, which can be flanged, coupling and welded (soldering), and the materials of manufacture, where steel, brass, polyethylene and polypropylene are used.

Different locking devices may have their technical characteristics and differ from each other in these indicators, which will be discussed below. And also your attention will be offered a thematic demonstration of the video in this article.

Stop valves DN 50 mm

Note. If you look at the label, the ball valve 50 mm usually has an additional abbreviation in the designation. For example, in front of millimeters there are letters Doo or Dn - and one and the other means conditional or outer diameter. And here, if you meet the abbreviation of KSHTsP (instead of P may be F, M or K), then this will mean that you have a full-welded ball-type ball valve (flanged, coupling or combined) in front of you.

Common parameters

Shut-off valves with flange, welded (for welding) and coupling connection are usually made in the range of DN from 15 to 500 mm, which is designed for a nominal pressure (Ru) from 1.6 to 4.0 MPa.
In most cases, cranes with such dimensions (Dn 50) are used in industrial, industrial and public buildings, pipelines pumping oil products, water and gas, as well as in tanks for their storage. However, locking devices with such dimensions are installed with their own hands and in everyday life, for example, with autonomous heating for risers, boilers or in tanks for storing water and diesel fuel.
The manufacture of valves and fittings is carried out in accordance with GOST 21345-78 and GOST 28343-89, as well as in accordance with TU 04671406-003-98. For regions with a temperate and cold climate, certification is carried out according to UHL GOST 15150 of the GOSGORTEKHNADZOR of Russia.

Product overview

Such cranes are usually made of steel Art. 20, 09G2s and 1218N10T, while the maximum working pressure (Ru) remains unchanged - from 1.6 MPa to 4.0 MPa. Methods of installation (connection) may vary depending on the configuration, so it can be KShTsF, KShTsP, KShTsM or KShTsK.

DN	PN	CODE KShTsF	d	D	D1	D2	G	h	H	I	L	Mass (kg)
15	40	015.040.02	ten	95	65	14	four	23	72	170	130	1.8
20	40	020.040.02	15	105	75	14	four	23	72	170	150	2.2
25	40	025.040.02	18	115	85	14	four	21	75	170	160	2.7
32	40	032.040.02	24	135	100	18	four	21	75	170	180	3.7
40	40	040.040.02	thirty	145	110	18	four	44	92	235	200	4.6
50	40	050.040.02	40	160	125	18	four	44	100	235	230	6.1
65	sixteen	065.016.02	49	180	145	18	four	44	110	235	270	8.4
65	25	065.025.02	49	180	145	18	four	44	110	235	270	8.4
80	sixteen	080 / 70.016.02	63	195	160	18	four	60	141	335	280	11.2
80	25	080 / 70.025.02	63	195	160	18	eight	60	141	335	280	12
100	sixteen	100 / 80.016.02	75	215	180	18	eight	60	150	335	300	15
100	25	100 / 80.025.02	75	230	190	22	eight	60	150	335	300	15
125	sixteen	125 / 100.016.02	100	245	210	18	eight	94	195	525	325	27.5
125	25	125 / 100.025.02	100	270	220	26	eight	94	195	525	325	28.5
150	sixteen	150 / 125.016.02	125	280	240	22	eight	98	210	525	350	36
150	25	150 / 125.025.02	125	300	250	26	eight	98	210	525	350	37
200	sixteen	200 / 150.016.02	148	335	295	22	12	84	225	625	450	56
200	25	200 / 150.025.02	148	360	310	26	12	84	225	625	450	57
250	sixteen	250 / 200.016.02	200	405	355	26	12	100	270	625	530	83
250	25	250 / 200.025.02	200	425	370	thirty	12	100	270	625	530	85
300 *	sixteen	300 / 250.016.02	240	460	410	26	12	167	634	-	750	155
350 *	sixteen	350 / 300.016.02	300	520	470	26	sixteen	196	690	-	750	276
500 *	sixteen	500 / 400.016.02	390	710	650	33	20	170	870	-	990	610

Technical parameters for KShTsF

Note. KShTsF for the most part is used on industrial sites.

Ballomax DN, (mm)	art.	Front door	DH	d	t	L	Н1	H2	BUT	Weight, kg
ten	71 .102 .010	ten	38	17.2	1.8	210	50	116	140	0.8
15	71 .102 .015	ten	38	21.3	2	210	50	116	140	0.8
20	74 .102 .020	15	42	26.9	2.3	230	47	115	140	0.8
25	74 .102 .025	20	51	33.7	2.6	230	47	120	140	one
32	74 .102 .032	25	57	42.4	2.6	260	48	124	140	1.4
40	74 .102 .040	32	76	48.3	2.6	260	41	129	180	2.1
50	74 .102 .050	40	89	57	2.94	300	41	135	180	3

Table of parameters KShTsP Du 10-50 mm Ru 4.0 MPa (40kg / cm2)

Designation KSHZ RMHS (RMUS)	DN	L	G	A	H
16-6	6	70	1/4	112	110
25-6		76
40-6		76
16-10	ten	75	3/8	112	134
25-10		80
40-10		80
16-15	15	85	1/2	125	123
25-15		105
40-15		105
16-20	20	95	3/4	136	134
25-20		110
40-20		110
16-25	25	105	one	127	174
25-25		120
40-25		120
16-32	32	120	1 1/4	215	184
25-32		145
40-32		145
16-40	40	130	1 1/2	215	231.5
25-40		150
40-40		150
16-50	50	150	2	280	233
16-65	65	185	2 1/2	280	233
16-80	80	205	3	342	330

Table of dimensions and mounting dimensions KSHTsM Du 6-80 mm

Plastic ball valve 50 mm SDR11 (polyethylene)

View. Application	For gas 10 bar, for water 16 bar
SDR	SDR11
Material	PE80 / PE100, PE2406 / PE3408
Opening / closing	? turning
Temperature	From -29 to 600С
Type of passage	Full bore
Auxiliary rod type	Telescopic extension
Purge Type	Without purge, 1 purge, 2 purge
Body welding and socket	Electric or coupling
Test Standards	EN 1555, ANSI / ASTM B16. 40

SDR11 table

Note. Polyethylene devices are used for underground installation.

Dimensions of ball valve DN50 mm KShTSK, the same as in KShTsM

Combined cranes are not much different from coupling valves, however, as well as their price, only KShTsK can also have an American, fitting or filter instead of external pipe threads and then their cost increases.

Polypropylene devices are extremely popular for plumbing and heating circuits for autonomous heating - in most cases it is now that metal is preferred by PPR and this is not surprising. Such units are able to withstand operating temperatures up to 100? C and operating pressures up to 10 bar, which is quite enough for normal conditions. Docking of similar devices with the pipeline is performed by soldering or welding with a special soldering iron.

Conclusion

In conclusion, it should be said that in everyday life you can mainly use brass KShTsM and KShTSK, as well as polypropylene solder taps. You can always install them yourself, if this will follow the instructions from the manufacturer.