How to clean water from wells from unwanted impurities
Well at home greatly simplifies life. She will always help out with the implementation of irrigation of plant crops, ensure the full operation of the bathroom, washing machine and shower almost for nothing.
If you want to have more access to drinking water, you should take care of its cleaning, since it does not always meet the permissible norms.

Types of pollution and methods of their elimination
A person is 80% of the water, so the topic of cleaning it before use is very relevant. This is the guarantee of our health.
But the fluid can be soiled that it can adversely affect not only the human body, but also the plumbing equipment. Therefore, you should start by eliminating just such a problem.
Silting

In the process of long idle water in the mine silts up. Its use becomes invalid.
Tip: it is recommended not to drill wells in rarely visited summer cottages. Because there the silting process is observed most often.
Consider how to clean the well from sludge:
- Deep well pump. We submerge the apparatus on the bottom and pump out all the garbage. This is the easiest and at the same time effective method performed by yourself. True to the mines, the depth of which exceeds 20 m, it does not fit.

- Gone. Pretty time consuming task requiring an assistant. The unit itself has the appearance of a metal pipe with a mesh closed top. Bottom is the bottom-washer, which does not allow the steel ball closed inside to fall out.
Application instruction looks like this:
- We tie the shell to the cable and drop it to the bottom of the shaft.
- Raise 50 cm and sharply lower again down.
- For a couple of seconds, until the lower hole blocked the ball, it has time to collect water.
- We repeat this action 3-4 times, after which we take out the device and clean it from the accumulated dirt.

- Two pumps included in one circuit. This method is called mechanized. It has high efficiency, perfectly removes lime, and is adapted for any depth.
The essence of its application is as follows:
- At the bottom, as in the first case, we place the vibration pump.
- The liquid pumped by him is supplied by means of a hose to a reservoir located on the surface. It has a fine mesh for filtering sand, clay, silt.
- Filtered water with the help of the second pump is delivered under pressure back into the well, which causes lifting from the bottom of all kinds of garbage. That contributes to better well cleaning.

We answered the question "how to clean a water well?" But this does not guarantee the purification of water to the level of drinking, because it may contain a mass of harmful elements.
Iron
In the ground quite often lies brown, red or magnetic iron ore. Its presence may necessitate the purification of water from iron, since in such a case its amount can reach up to 0.5 milligram per liter. And such a concentration can harm not only man, but also expensive plumbing.
Tip: be sure to perform a chemical analysis of the fluid from the well. Because the cost of negligence can be much higher than the cost of the lab.
The purification process is set:
- Compressor for air injection.

- Aeration, which will mix the liquid with air.
- Filter iron remover with loading.
Reagents can also be used, but the source can then remain unsuitable for drinking for a long time.
Other impurities
The ingress of sewage, the spread of harmful bacteria, the presence of salts, all this in high concentrations makes water undesirable for domestic consumption. How to clean the water from the well in this case?
Consider a few ways:
- Boiling. This method is familiar to us from childhood. But it should be borne in mind that he copes with organic matter, and heavy metals and chlorine, on the contrary, only catalyzes. So we will not solve all the problems.

- Upholding. Efficiently enough, until dust gets inside. After this begins the rapid reproduction of bacteria. Everyone probably paid attention to the greening bottom of the plastic bag?
- Freezing. Melt water is very useful with proper technology, but the process itself is time consuming and limited by the capacity of your freezer.

- Filter. The most reliable option. Depending on the quality of the well filtration system, you will receive a guarantee of clean water. In modern models there are several filters:
- carbonic,
- rope,
- coconut,
- reverse osmosis membrane,
- quartz.
The whole complex removes bacteria, heavy metals, unpleasant odors and enriches with useful substances.

Conclusion
If you want to drink water from your own well and are not afraid for sensitive plumbing, then think about cleaning it. But first of all, of course, it is necessary to do a fluid analysis in order to know what you will have to contend with. It may even be that the source is not at all suitable for use.
Next may follow several stages of cleansing work. From the removal of debris from the mine itself, which usually occurs in the silting process, to filtering the water inside the house from all kinds of bacteria, impurities and toxins. Choose a set of measures that suit you and get to work.

The video in this article will provide you with more information regarding this topic. Take care of clean water in your own home first.