Water dripping from the tap - possible causes and their
Many start repairs only when a defect in the plumbing becomes very annoying, this is directly related to the faucet, the water from which, dripping, begins to act on the nerves. We recommend that you tackle this problem as quickly as possible, otherwise a small trickle will soon appear, and behind it the mixer will fail.
Do not forget also about finances that run away just like that to the sewage system in houses equipped with meters. Below we will deal with the defect - to detect its cause and how to eliminate it.

Possible causes of leaking tap
They are actually not so many, so consider the most common:
Substandard mixer | In pursuit of an inexpensive thing, many simply do not understand that the price of high-quality sanitary ware cannot be low. As a result, consumers rejoice at models that can only be conventionally called mixers. The joy of the "saved" means evaporate in just a month. The reason will be the refusal of the crane in the work or even an emergency situation because of it. Well, when in the house at this moment, someone will, and if not? You will have to spend on eliminating the consequences of not only time but also money. We recommend not saving on the purchase of a crane - the product should be from a manufacturer who has long established itself in the market. At the same time, a very low cost of a branded product will be a sign of a fake. |
Wrong device installation | Although there is nothing difficult in installing the mixer and you can easily install it yourself, there are often mistakes made during the assembly of the device. We advise you not to rush after purchasing quality equipment and perform all the steps recommended by the installation instructions. |
Violation of the rules of operation of the device | Do not forget, each mixer has its own operational features. The manufacturer knowingly prescribes them in his memo. Under these conditions, it guarantees the normal operation of the device within the specified period. Frequent oversights that lead to plumbing defects:
|

Another reason - the natural wear and tear of equipment. Failure of the moving elements of the crane, often rubber gaskets.
Tip: to avoid a sudden accident, it is necessary to periodically carry out preventive maintenance of the device, replacing worn gaskets.
Alas, the overwhelming majority of users do not do this, and pay attention to the problem when it has become particularly pronounced. Below we will deal with its elimination of their own hands.

Training
We will single out 4 main points guaranteeing uninterrupted product operation:
- The right choice of crane and its elements.
- Install the device according to the manufacturer's instructions.
- Proper operation of the equipment.
- Carrying out preventive work.
And yet, the faucet began to flow, what to do in this case?
- First, determine the source of the leak, for this look at how the water behaves, which can:
- to leak or drip from under the inclusion valve;
- drip or flow in a thin stream with the spout valve closed;
- flow at the junction between the spout and the mixer;
- flow at the point of connecting the water pipe to the mixer;
- leak at the installation site of the tap to the sink.
The body of the product can also be damaged, from which water can also flow.
- Shut off the water flow into the mixer (hot and cold) after finding out the cause of the leak.

Process
We will consider each cause separately:
- If water seeps or drips from under the valve, most often this is due to the valve box not fitting tightly to the mixer or due to wear of the rubber pads.. To eliminate the defect, you can replace the rubber gasket and draw a crane box. If the latter is ceramic, you need to seal the silicone gland that is installed on it.
- When water flows from a spout like a thin stream or drips, it is most likely caused by a blurred crane cock.. This does not completely block the water. Typically, such a failure occurs in low-quality low-quality equipment.

Defect is eliminated by replacing the crane box and / or installing another valve. If all else fails, you need to change the mixer. Note that the wear of the cock-box and gaskets may occur due to the roughness of the inside of the defective product.
- If water leaks at the attachment point of the spout to the valve body, the cause may be wear of the gaskets and unwinding of the spout due to prolonged use or damage.. You can eliminate it by replacing the gaskets and tightly tightening the spout to the body of the product.
- In the case when the water flows at the junction of the water pipe with the mixer, most likely an installation defect. This is usually due to excessive force when tightening the nuts, which caused damage to the gaskets. Another reason - the use of low-quality hoses. The problem is solved by replacing gaskets or replacing hoses.
Tip: Do not over-tighten the nuts so as not to damage the gaskets again and prolong their service life.

Materials and tools for self-repair
You can buy them in any hardware store, and you probably have many in your apartment or house:
- spare crane box;
- a set of keys, a gas key;
- glue;
- screwdrivers;
- gaskets of different sizes and from different materials;
- fum-tape or tow;
- silicone seals.
Conclusion
When the faucet flows in the kitchen or in the bathroom - it is not only unpleasant, but also expensive. Before you repair the defect, you must determine its cause. Repair work is simple, but requires compliance with certain rules. The video in this article will provide an opportunity to find additional information on the above topic.