What should be the water pressure in the faucet, how to
The water supply system is a complex structure of pipes and water intake points. The movement of water is carried out due to internal pressure in the pipeline. How it should be and how it can be changed, we will consider in this article.

General regulations

The pressure in the water supply is usually measured in bars or atmospheres, with 1 bar equal to 1,0197 atm., Which does not make a significant difference. But what should be the rate of water pressure in the faucet? First of all it depends on what you plan to use the water intake point for:
Pressure bar | Opportunities |
Less than 1 | None due to the absence or extremely small size of the jet. |
2 | It is an acceptable figure, at which it is quite comfortable:
|
four | It already opens up the possibility of operating more demanding equipment:
|
More than 6 | It turns out to be a devastating effect on all connected plumbing fixtures and ceramic faucets |
Tip: for apartments connected to the urban water supply system, it is recommended to buy plumbing, which has a certain margin of safety, which will allow to transfer hydraulic shocks and unauthorized pressure surges. The higher price of such equipment is more than repaid due to the possibility of long-term operation in extreme conditions of the city.
But how do you know the pressure in your apartment or house? Let's look at this point in more detail:
Barometer

Before you measure the power flow in the water supply you need to prepare the necessary materials and tools:
The designation on the photo | Title | Purpose |
one | Manometer | Pressure determination |
2 | Thread Extender | Gauge connection |
3 | Adapter | |
four | FUM tape | Sealing threaded connections |
How to measure the required parameter with the help of these components:
- With our own hands we wind the FUM tape on the threaded pipe connections and connect all the details.

- We go into the bathroom, we take a shower and we twist a watering can from it.
Tip: in the implementation of the described manipulations, try not to lose the rubber gasket from under the watering can, which is responsible for its tightness.
- Screw the gauge on the free space.

- Turn on the shower and look at the pressure gauge.
Depending on the results obtained as a result of verification, it is necessary to decide what to do next. After all, if, for example, the device showed 2 bar, and you plan to connect the jacuzzi, then you need to increase the pressure in the system, not to mention the variant, which turned out that in your pipes no more than 1 bar.
Replacing the crane without shutting down the riser

Once we have touched on technical issues, then let's deviate a little from the topic and examine the question that is of interest to many: how to change the tap under the pressure of water? Situations can be different, and it is not always possible to disable the riser.
Then you need to do the following:
- We put an empty container under the old faucet to avoid flooding.
- We wind the threaded connection of the new FUM product with tape.
- Then open both the tap and replace them. The trick is that when the valves are open, the pressure exerted by the water will not interfere with the process.
The increase in pressure in the water supply
Most often, the need to increase the intensity of the water flow occurs on the upper floors of multi-storey buildings or in country houses connected to water towers.
Tip: before applying drastic measures, first check the condition of the pipeline for clogging, since the reduction of the internal passage due to accumulations of debris is also a cause of pressure drop. In this case, either cleaning or replacement of pipes will help.

The instruction offers a choice of three ways to solve the problem of low pressure.
Method # 1: circulation pump

It is possible to buy and install a circulating pump directly in front of the water intake point, which will be able to more intensively draw water from the pipeline, increasing the flow.
According to the mode of operation, the pumps can be:
- Hand held Relatively cheap models that need to be monitored in the course of their operation and periodically turned off so that they do not burn out.
- Automatic. More expensive, but completely autonomous samples.
Method number 2: pumping station

This equipment consists of three elements:
- The centrifugal pump providing increase in power of a stream in system.
- Hydroaccumulator up to three cubic meters.
- Pressure switch controlling the whole structure.
A special advantage is the ability to provide a pressure level of up to 4 atmospheres even in the case of periodic shutdown of the water supply. The fact is that while there is an influx, the pump works by accumulating the tank, and then the device spreads the liquid through the pipes to the points of consumption.
Cons, which must be considered:
- Enough high cost.
- Large size.
- The need for periodic cleaning of the hydroaccumulator.
Method number 3: autonomous water supply

A well with water-lifting equipment is a very expensive and time-consuming business, besides, its implementation is possible only in suburban areas. But in this case, you yourself will not only determine the level of pressure in your plumbing system, but also get complete independence from public water supply, with its constant interruptions and low-quality water.
Conclusion
We looked at how to check the pressure in the plumbing system and, if necessary, increase it. Each method has its own characteristics, so the choice should be made individually according to your situation.

The video in this article will introduce additional materials. Watch for the level of pressure in your water supply system.