What to do if the faucet in the bathroom flows: causes of
Probably, there is no such person who did not find once dripping water from a tap. The problem crept imperceptibly and, as always, at the most inappropriate time.
We postpone the repair, cause the locksmith is also too busy, in the end, a modest "cap-cap" turns into a blatant stream. Further rusty stains on the bathroom and the sink, and even elemental deluge. But to fix the problem yourself in most cases is not difficult.

We are looking for the cause of the leak and eliminate it.
First of all, it is necessary to find out why the faucet is flowing in the bathroom and what caused it. Naturally, we immediately see where it is dripping or beating with a trickle. Later it is necessary to find out what part (s) are located in this area.
Note! Before rushing to combat leakage, shut off the water supply to the mixer. Every owner should know where the shut-off valve is located - under the sink, in the mine or in the basement.
Laying out of use

In many apartments there are still valves of the old valve type, with rubber gaskets. Usually a tap in the bathroom flows due to abrasion of the seal. The gasket is in contact with water, rubs against metal parts, sometimes dries.
It has to be changed once a year or two, or even more often.
- Remove the protective cap from the valve. The blue cap is on the cold water tap, the red one is on the hot one.
- Under the lid, you will see a screw securing the crane handle. Unscrew it and remove the handle.
- If there are decorative plates, screw them too, then you will see a crane. It is removed using a gas or adjustable wrench.
- On the back of the axle box, a round gasket is fixed, due to which the faucet in the bathroom dripped. It is screwed with a screw, it must be unscrewed with a screwdriver.
- After removing the old gasket, replace it with a new one.. Moreover, the finished store can be replaced with a homemade, cutting it out of a piece of rubber or thick leather.
- All subsequent assembly steps are done in reverse order..
Note! When disassembling the crane parts unscrew counterclockwise. When reassembling - hourly.
Seal Replacement

Often, rubber seals flow in places where the mixer and supply pipes mate.
And this trouble can be fixed with your own hands, with the help of an adjustable wrench and a screwdriver.
- Shut off the water supply to the mixer, after identifying the leak.
- Unscrew the retaining nut connecting the pipe and the mixer.
- Inside the ring is inserted from the rubber, it will have to be replaced.
- After neatly fitting the new ring, assemble the system. Be sure to use a winding (tow or fum tape), then the joint will turn out absolutely tight.
Change the hose gasket from the shower
Most often the shower is leaking at the point where the hose connects to the mixer.
- Unscrew the shower hose with an adjustable wrench.
- Carefully, in order not to damage the hose thread, remove the seal.
- Insert a new gasket and screw the part neatly into place as well.
Note! Instead of rubber gaskets and rings instruction advises to purchase silicone counterparts. They are more durable and stronger, less responsive to abrasion and mechanical stress.
Flowing ball valve

More recently, lever devices have gradually appeared that are gradually replacing the usual valve devices. Now we see one pedal, simultaneously regulating both the pressure and the flow temperature.
How to fix it - if the faucet in the bathroom flows, if you are completely unaware of what is inside it?
- Most likely, the ball or cartridge inside the sink mixer device is leaking. Often, scale fragments fall between it and the body, creating cavities sufficient to allow water to seep through.
- Remove the decorative cover and unscrew the screw with a screwdriver.
- Remove the lever from the valve and unscrew the threaded screw.
- Separate the dome and plastic seal.

- On the seal gasket most likely accumulated plaque, it should be cleaned.
- Rinse the parts with hot water and assemble the system.
Note! If, when inspecting a disassembled instrument, you find one or more parts in a badly battered condition, try replacing them with new ones. Otherwise, even a cleaned mixer will break completely in the near future.
Expert advice

Many unpleasant situations can be avoided if you properly use the plumbing and occasionally perform preventive actions.
The prudent owner knows not only how to eliminate a leak from a faucet in a bathroom, but also how to maximize its performance.
- When purchasing plumbing fixtures, be sure to request a warranty card. Do not buy faucets and parts from random people, they are not responsible for the marriage.
- Do not wait until the leak reaches a maximum, repair the taps at the drops stage.
- If you, for various reasons, do not use one or several taps for a long time, periodically open and close them. This will prevent boiling and seizure of the system.
- Do not spare money to replace a broken item. Its price is in any case lower than the cost of the new mixer.
- In the course of repairing plumbing equipment, it is often necessary to rush to the store for the necessary part in a hurry. Be sure to take with you the broken one, show it to the seller. He will understand exactly what to offer you in return.
- Doubt in your abilities, invite a specialist from the housing department. An unfamiliar master you are unlikely to be able to make a complaint for bad work.
Conclusion
With every drop of water your money is leaking. Prevent this easily by paying attention to your plumbing fixtures. Research shows that repair costs are many times less than paying bills.
The proposed video in this article will teach competent repair and prevention problems.